Foam Board Insulation

With the various types of insulation boards you can purchase for your construction project, it is important to know which type is necessary for that specific project. In cases where a basement or space doesn’t need insulation for framing the walls, blue board insulation can be your best option. It can keep the insulation in your home.

Another term for this type of insulation is rigid foam insulation. It is sold in sheets. All you need to do is to attach it directly to the wall. If you will compare it with other types of insulation, there is still a need to put some dry wall over these blue board insulation sheets.

For those with Small Areas at Home

If you live in a small-spaced apartment or home, using blue board insulation on the walls is a good option. It’s better than using blanket insulation because the latter still needs building framed stud walls. To attach blue board insulation directly to the walls, you just need furring strips. After attaching the board, you only need to cover it with a drywall sheet. Just expect that you’ll also be cutting down an inch or two of space from your room.

A good way to save money is to just insulate the outside walls. This also makes the space more energy efficient.

On Cold Climate Areas

The reason rigid foam insulation is good for homes in cold climate areas is the fact that it can provide a higher RSI value as compared to those with blanket insulation. Keep this in mind: The higher the thermal insulation properties, the higher the RSI value. With the high RSI value and board construction, this type is preferred on walls where drafts pose a problem.
Avoiding Vents & Lights

If you will be installing insulation, make sure you avoid light fixtures, lights and even heating vents. Though these insulations are fire resistant, they can still be flammable and there are times when they lead to fire when situated too close to a hot light or on a heating vent. It is better if you will place it 3 inches from the edge of these vents or lights. It is also very important that you don’t cover a vent with this type of insulation board.

When Cutting Size

To ensure a snug and comfortable home, you need to cut these boards to size. It should fit snugly to the space you are installing it to. Never leave gaps between the edge and the wall near it. If there are gaps, the wall may let it cold spots or drafts. This keeps the space from being energy efficient.

Article source: http://www.articlesbase.com/home-and-family-articles/installing-blue-board-insulation-boards-4384843.html

Among the most effective and easy-to-install insulation choices for your enclosed carport, garage or metal building is foam board. The same stuff that NASA has used to insulate a space shuttle’s external tank, keeping its liquid hydrogen fuel at minus 423ºF and its liquid oxygen tank at near minus 297ºF to prevent ice buildups on the inner fuel tank’s exterior surface, can be used to keep your metal carport  toasty in the wintertime and cool during the summer.

While fiberglass insulation works by slowing down the rate of passage of heat into your home during hot summers and out of your enclosed carport, garage or metal building in winter, foam board insulation brings that passage to a halt by completely sealing all cavities and spaces in your structure’s walls. These unsealed voids are the primary source of energy loss, which means more money out of your pocket and into your energy provider’s coffers.

Enclosed car port foam board is a bit more expensive than fiberglass and may require professional installation. But its “R value” (its measure of thermal resistance) can be three times that of fiberglass. The higher a structure’s R value, the better its insulation’s effectiveness. If you plan to spend lots of time in your carport, garage or metal building (for instance, if you plan to use it as a workshop, office or recreational room), the long-term energy cost savings over fiberglass can be significant.

Foam board insulation can be applied to steel carports, enclosed garages or pole building in several ways: as rigid panels attached to your carport, garage or metal building inner walls or as a chemical mixture prayed from aerosol containers or a pressure sprayer (A third method involves foam board in the form of loose beads poured into masonry blocks in more traditional construction). Rigid foam board insulation typically comes 4’x8’ sheets and can be cut to fit your structure’s walls using a craft knife or fine toothed handsaw, then applied to your walls using construction adhesive. Two important notes: 1) Because foam boards absorb water vapor, you must cover the insulation with a moisture or vapor barrier and 2) because foam board is flammable, building codes in virtually all areas require that it be covered with fire resistant paneling or drywall.

Foam board also can be sprayed directly on to your walls via aerosol containers or pressure sprayers. It is recommended that you hire a professional installer for this method, as it can involve complex equipment. And because foam boar seals your enclosed carport, garage or metal building so tight, an air exchange may need to be installed. However, this results in superior indoor air quality because air pollutants such as pollen and dust have no way in. Foam board insulation also can help ward off mold, pest and insects for most enclosed carports.

Article source: http://www.articlesbase.com/industrial-articles/foam-board-insulation-for-your-enclosed-carport-garage-or-metal-building-1812042.html